9 stickers from shoes manufacturerGuests receive a film or document, to conduct the production model, to be carried out upon confirmation sample before mass production.
a. stickers are divided into: transparent stickers, barcode stickers, color stickers.
i. transparent stickers commonly used materials: 25 # PET transparent film, PP, PVC and so on.
ii. barcode stickers: make a good sample bar code label printer to be tested too, and then the guests confirmed only after the production.
iii. Printing Stickers: Film production provided by the guests as needed, over the surface of varnish or too PP plastic, etc., pay attention to the color of the sample with the guests to try the same or similar.
b. sticker prepare plastic material:
500 3M successive ordinary strength trying to strengthen powder force.
10 Blister
1) commonly used plastic materials VC, PP, PET and so on.
2) design Note:
a. injection button can not be done bit parts in order to avoid scratches.
b. white PET high cost, use less, when a large number of orders, the supplier will provide material, so unless requested Party may consider the use of special guests.
c. Blister methods are commonly used:
Heaven and earth cover type, cover type buckle, buckle-position, plug-in, hot style and so on.
i. designed with which, according to the product shape and requirements of the guests, and generally when a world-lid and snap-in plastic cover, there is not usually affixed to the window box film.
ii. designed to monitor, for the shape more complex products and products with fuel injection parts, considering Gato plastic, plastic tray and plastic materials are generally the same.
d. Blister common # sign films, as referring to the thickness of the sheet to 0.35mm for the common sheet.
e. Avoid using colored plastic suction to prevent cost increases.
11 Blister Card
For plug-and hot-style plastic, usually use blister card design attention to the following:
a. Plug-in blister card
Blister card Blister with plug-in assembly, called plug-in blister card.
When do first blister card, do the blister, you need to be equipped to avoid too tight or blister card into the long, plastic card surface generally had to be polished or varnished or too PP plastic, etc., depending on the request. be.
b. pressing style blister card
Blister card Blister with hot-fit assembly, called the hot style blister card.
Design should pay attention to the surface of the plastic processing, plastic card surface to be too plastic oil such as plastic material is PET, the plastic card surface corresponding to cross APET green oil, or blister cards and plastic can not be hot pressure on bond.
c. Blister card Material:
As the case may be printed, when printed on one side only, the use of the paper ash. Commonly used gray powder 300g, 350g paper ash, 400g paper ash; when printing on both sides to be, with a double coated paper. Commonly used 300g double coated paper, 350g powder gray paper, 400g powder gray paper.
12) Poly (POLYLON)
This is not styrofoam, white vacuum formed, usually in the Japanese and European markets is prohibited.
13) bags from shoes factoryA. Press the material into plastic bags: single bubble bag, PE bags, PP bags, OPP bags, single-sided steam beads tablets.
B. divided by style: flat bag, bone bag, two through plastic bags, perforated plastic bags, plastic bags printing marks, covered plastic bags.
C. Common plastic representation
a. stickers are divided into: transparent stickers, barcode stickers, color stickers.
i. transparent stickers commonly used materials: 25 # PET transparent film, PP, PVC and so on.
ii. barcode stickers: make a good sample bar code label printer to be tested too, and then the guests confirmed only after the production.
iii. Printing Stickers: Film production provided by the guests as needed, over the surface of varnish or too PP plastic, etc., pay attention to the color of the sample with the guests to try the same or similar.
b. sticker prepare plastic material:
500 3M successive ordinary strength trying to strengthen powder force.
10 Blister
1) commonly used plastic materials VC, PP, PET and so on.
2) design Note:
a. injection button can not be done bit parts in order to avoid scratches.
b. white PET high cost, use less, when a large number of orders, the supplier will provide material, so unless requested Party may consider the use of special guests.
c. Blister methods are commonly used:
Heaven and earth cover type, cover type buckle, buckle-position, plug-in, hot style and so on.
i. designed with which, according to the product shape and requirements of the guests, and generally when a world-lid and snap-in plastic cover, there is not usually affixed to the window box film.
ii. designed to monitor, for the shape more complex products and products with fuel injection parts, considering Gato plastic, plastic tray and plastic materials are generally the same.
d. Blister common # sign films, as referring to the thickness of the sheet to 0.35mm for the common sheet.
e. Avoid using colored plastic suction to prevent cost increases.
11 Blister Card
For plug-and hot-style plastic, usually use blister card design attention to the following:
a. Plug-in blister card
Blister card Blister with plug-in assembly, called plug-in blister card.
When do first blister card, do the blister, you need to be equipped to avoid too tight or blister card into the long, plastic card surface generally had to be polished or varnished or too PP plastic, etc., depending on the request. be.
b. pressing style blister card
Blister card Blister with hot-fit assembly, called the hot style blister card.
Design should pay attention to the surface of the plastic processing, plastic card surface to be too plastic oil such as plastic material is PET, the plastic card surface corresponding to cross APET green oil, or blister cards and plastic can not be hot pressure on bond.
c. Blister card Material:
As the case may be printed, when printed on one side only, the use of the paper ash. Commonly used gray powder 300g, 350g paper ash, 400g paper ash; when printing on both sides to be, with a double coated paper. Commonly used 300g double coated paper, 350g powder gray paper, 400g powder gray paper.
12) Poly (POLYLON)
This is not styrofoam, white vacuum formed, usually in the Japanese and European markets is prohibited.
13) bags from shoes factoryA. Press the material into plastic bags: single bubble bag, PE bags, PP bags, OPP bags, single-sided steam beads tablets.
B. divided by style: flat bag, bone bag, two through plastic bags, perforated plastic bags, plastic bags printing marks, covered plastic bags.
C. Common plastic representation
a.PE or PP flat bags:
The seal is usually about 5 ~ 8mm, expressed as:
5x8 "represents five" as the opening; 8x5 "indicates 8" openings.
b. bone bags, commonly known as the zipper bag:
5x8 "represents five" as the opening; 8x5 "indicates 8" openings.
c. no sealing plastic bags:
5x8 "means that two-pass. D. Perforated plastic bags with holes for ventilation.
5x8 "playing two holes.
e. printing bags:
PP 5x8 "print, playing two holes must be marked with the contents and location of India.
f. steam beaded bag
To specify single or double, with other dimensions described above:
i.PP sided bubble bag, 5x8 "represents five" as the opening.
Single-sided or double-sided steam vapor sequin beads
Covered plastic bags (side length short side)
50mm +120 mm +25 mm;
ii. material thickness
Generally use 0.03mm, special situations using 0.05mm.
iii. Design Considerations:
When the bag is relatively large, it is necessary to punch holes in the plastic bag to prevent child set into the header of suffocation.
14) specification and postal cards
Upon a model and film to make, usually first recognized as a model to the guests before for mass production.
15) EPE
Generally used for the vibration, this is rarely used, a thickness of about 2mm.
16) Ties
a. outer colored plastic into flat and round shape, generally black colloid.
b. using cable ties form package, including possible back of the card plus table cards or plastic sheets to prevent cracking or tie loosen the Neckar.
Three For QA testing
1, the contents of the test
See QA testing standards
Four. Packaging Design Considerations from women shoes manufacturer1 box using PEV films, be sure to add paper Cowper separated.
2 Cartoon Test
Generally fall vibration check box
3 fixed frequency (typically a variable frequency vibration table when a face turned every 10 minutes, a total of three surface 30 minutes. If slight fade ----- B surface as OK.
4 injector or screen printing surface minor abrasions, you can add "saving" finishes.
5 cartoon objects must be within the relatively tight, such as loose, scratch box appears phenomena
The seal is usually about 5 ~ 8mm, expressed as:
5x8 "represents five" as the opening; 8x5 "indicates 8" openings.
b. bone bags, commonly known as the zipper bag:
5x8 "represents five" as the opening; 8x5 "indicates 8" openings.
c. no sealing plastic bags:
5x8 "means that two-pass. D. Perforated plastic bags with holes for ventilation.
5x8 "playing two holes.
e. printing bags:
PP 5x8 "print, playing two holes must be marked with the contents and location of India.
f. steam beaded bag
To specify single or double, with other dimensions described above:
i.PP sided bubble bag, 5x8 "represents five" as the opening.
Single-sided or double-sided steam vapor sequin beads
Covered plastic bags (side length short side)
50mm +120 mm +25 mm;
ii. material thickness
Generally use 0.03mm, special situations using 0.05mm.
iii. Design Considerations:
When the bag is relatively large, it is necessary to punch holes in the plastic bag to prevent child set into the header of suffocation.
14) specification and postal cards
Upon a model and film to make, usually first recognized as a model to the guests before for mass production.
15) EPE
Generally used for the vibration, this is rarely used, a thickness of about 2mm.
16) Ties
a. outer colored plastic into flat and round shape, generally black colloid.
b. using cable ties form package, including possible back of the card plus table cards or plastic sheets to prevent cracking or tie loosen the Neckar.
Three For QA testing
1, the contents of the test
See QA testing standards
Four. Packaging Design Considerations from women shoes manufacturer1 box using PEV films, be sure to add paper Cowper separated.
2 Cartoon Test
Generally fall vibration check box
3 fixed frequency (typically a variable frequency vibration table when a face turned every 10 minutes, a total of three surface 30 minutes. If slight fade ----- B surface as OK.
4 injector or screen printing surface minor abrasions, you can add "saving" finishes.
5 cartoon objects must be within the relatively tight, such as loose, scratch box appears phenomena
没有评论:
发表评论