Kind of shoe mold

1. To be divided by material: outsole (RB), midsole (EVA), TPU, PU, ​​cushion, patch. RB which are: traditional RB, RB and injection foam RB. Midsole (EVA) is divided into: the traditional EVA (CP), injection EVA (IP) and 3DMF three.from shoes manufacturer

2. Press the parting line to be divided: No partakers mold parting line and line two.

3. Mold making way points are: carved wooden mold casting, engraved copper or graphite electrode discharge directly from the engraving engraved or NC mold three.

Various relevant term Xiemo
1. Shape: This is the most important shoe mold. Especially because of a change in shape of the mouth plate, 3D will be redone. And the mold plate-shaped mold is likely to go wrong scrapped. Shape are: the last head plate (LAST), leather board (TOP NET), which Union Board (TOP), also known as the mouth plate, on the outer plate (TOP OUT), bottom (BOTTOM), the outer panel, inner panel ( LATERAL), lateral plate (MEDIAL), keel plate (SEC AA), off the panel (SEC BB), front view (FRONT VIEW), rear view (HEEL VIEW).

2. Flesh: flesh into total basic flesh.

3. Other related terms: every color channel, retaining wall, reinforcement, toilet seat (TOE SHELF), curved ditch, inside R, shrink, mold base, public mode (wooden mold), level volume of production, expansion ratio, reduced image , RP (STL files), oblique sweep, push-type edge trimming.

Explanation of related terms
(1) flesh: generally refers to the thickness of the RB. RB overall total thickness of both flesh; basic RB refers to the flesh to ensure minimal thickness, typically 1.5mm or 1.8mm.

(2) every color channel: not only cut off on alternate colors to a different color walls, because the finished product is concave so called every color channel.

(3) wall: Generally speaking, there are two retaining. First, because the gap is too small ditch and easy color gamut and next to it to make a 1.2 * 1.2mm (width * height) across the slope to enhance the color, this is called a retaining wall slope. Another is the rule pattern (especially water ripple) boundary, it also has to play the role of color separated. This wall generally wide 1.0mm.

(4) Reinforcement: Refers to every little flesh-colored ditch at the time, including the kernel to do about 0.7mm deep concave arc to strengthen across the ditch flesh color, so it is not easy to disconnect RB finished.

(5) toilet seat: common in basketball shoes and tennis shoes. RB toe portion shaped like a toilet fit gap is called the toilet seat.

(6) bending groove: EVA usually refers to a small front pocket groove, its role is to make the shoes more comfortable when walking bent. Generally done on the inner benevolence, and sometimes do at the bottom. Generally do 2.5mm deep.

(7) within the R: R is the number on the inner kernel.

(8) shrink: refers to the material after molding at high temperature is gradually cooled to room temperature, the ratio will be reduced. Common has shrunk: RB shrunk 1.022, CP shrunk 1.007 (1.018), iron shrunk 1.02, aluminum shrunk 1.011.

(9) mold base: According to the parting line of the mold strike and set a good standard size chart processing out of the mold surface wooden mold.

(10) male mold: made of wood substrate processing three-dimensional pattern of an entity.shoes factory

(11) level volume production: According to drawings made shoes called the code number (sample code). Subject to zoom in or out of the yard to do another number called the mass production of shoes.

(12) Foaming rate: refers to the mold material, the average IP magnification.

(13) Miniature: Refers to make IP mold material expansion ratio calculated in accordance with the finished drawing is reduced to 1:1 for IP mold size drawings.

(14) RP: refers to the method used to make the powder layer deposited 3D file of a physical three-dimensional pattern. So that customers can see them without opening the mold design patterns and structures.

(15) oblique sweep: 3D files to toe in the construction centerline and keel bottom warped point do prevail forefoot perpendicular to its surface curvature. This requires adjusting the inner and outer plates springing points and curvature, but the overall height of the side panel as to ensure that the drawing. After the toe ramp sweep to flush out the last part. Not oblique sweep approach is to mold centerline, the lateral pull done on the surface before Alice radians. So do not adjust the drawings, the lateral view.

(16) Push-type side trimming: Refers to the position of RB finished with perforated edges higher plane than the inner benevolence 3.0mm push knife edge burrs can repair a push out of the way. Another is Zhang chopper style, flash no higher than the surface of the inner benevolence sometimes do flesh, finished with a chopper to chop. from men shoes manufacturer